Release agents for imprinted concrete | Desmocem

Desmocem® is our exclusive range of release agents for imprinted concrete and vertical imprinted concrete. High-performance products that are designed to facilitate the removal of the molds used in the printing of pavements and walls.

Release agents for imprinted concrete that create a completely non-stick surface, prior to the application of the imprinted molds. In this way, it is possible to prevent the molds from adhering to the pavement or wall and not being able to provide their decorative texture.

Our release agents allow any type of template or mold of imprinted concrete and vertical imprinted concrete that is used, can make their mark in the cleanest way possible.

A product line in which we find on one hand Desmocem® Liquid, a liquid release agent for imprinted concrete; and on the other hand Desmocem® Powder, translate-tag>a release agent in powder version. This last one has the quality of also providing color, so all kinds of contrasts can be created, since there is no need to use the same tone as the mortar or wearing layer.

Release agent for imprinted concrete in liquid form

Desmocem® Liquid is the release agent for liquid imprinted concrete that is part of the Desmocem® release agent family from Topciment. In the same way as its counterpart in powder version, it is a release agent based on aliphatic solvents that perfects the removal of imprinted concrete molds and vertical imprinted concrete.

It is a liquid release agent for imprinted concrete based on solvents that does not require dilution and dries by evaporation. In fact, one of its most notable features is that it offers touch drying in just 1 hour.

Download the technical sheet of Desmocem® Liquid here

Technical features of liquid release agent for imprinted concrete

Density

0,68 ±0,01g/cm3

Insoluble in water

Touch dry (23ºC)

1 hour

Evaporation drying

Performance

The performance of the Desmocem® Liquid release agent for imprinted concrete is 15-20 m2 /L.

Presentation

The release agent for imprinted concrete Desmocem® Liquid is available in 5 and 18 liter containers.

Application
Precautions

How to apply the release agent for imprinted concrete

1. Spray the liquid Desmocem® imprinted concrete release agent directly onto the imprinted mold and the surface to be treated.

2. Print by applying certain pressure and demold the piece that has been used.

3. Apply the product using a sprayer, brush or roller. In the case that it is done with a sprayer, maintain a distance of between 30 and 40 cm of separation.

4. Coat the surface in such a way that a uniform and homogeneous film is applied. Avoid leaving puddles or placing very thick layers.

Regarding the application of this release agent for imprinted concrete liquid and insoluble in water, it should be noted that the ambient and support temperature must be between 5ºC and 30ºC without excessive wind. If by chance the temperature exceeded 35ºC it could cause excessive evaporation of the solvent. If that were to happen, it would therefore have to be reapplied the release agent.

Precautions for the release agent for imprinted concrete Desmocem® Liquid

The liquid and vapors are very flammable. A product that can cause skin irritation, drowsiness or dizziness.

In case the liquid release agent for imprinted concrete Desmocem® Liquid comes into contact with the eyes, clean with plenty of water for about 15 minutes and see a doctor.

If there is skin contact, wash the affected area with water and soap.

It is necessary to ensure good ventilation.

It is recommended to use a mask with chemical absorbent for organic vapors, protective glasses and rubber gloves.

Close the container lid after each use to prevent it from drying out or thickening.

Release agent for imprinted concrete in powder form

Desmocem® Powder is the release agent for imprinted concrete in powder form from the Desmocem® range by Topciment. A product created with the aim of improving the removal of the molds used in decorative concrete flooring.

A ready-to-use release agent that is made up of esterified fatty acid salts and completely inorganic pigments. A release agent for imprinted concrete in powder form, insoluble in water and with a range of 12 colors.

Desmocem® Powder is not only designed to facilitate the removal of molds in decorative surfaces, but it is ideal for obtaining decorative aging. An aging with which to give a touch of distinction to the imprinted pavements and to the vertical imprinted concrete.